Docs Menu
Docs Home
/
MongoDB Manual
/ / /

Read Preference Use Cases

On this page

  • Read Preference Modes
  • Indications to Use Non-Primary Read Preference
  • Counter-Indications for Non-Primary Read Preference
  • Maximize Consistency
  • Maximize Availability
  • Minimize Latency
  • Query From Geographically Distributed Members
  • secondary vs secondaryPreferred

The following document explains common use cases for various read preference modes, as well as counter-indications outlining when you should not change the read preference from the default primary.

Read Preference Mode
Description

Default mode. All operations read from the current replica set primary.

Distributed transactions that contain read operations must use read preference primary. All operations in a given transaction must route to the same member.

In most situations, operations read from the primary but if it is unavailable, operations read from secondary members.

Read preference primaryPreferred supports hedged reads on sharded clusters.

All operations read from the secondary members of the replica set.

Read preference secondary supports hedged reads on sharded clusters.

Operations typically read data from secondary members of the replica set. If the replica set has only one single primary member and no other members, operations read data from the primary member.

Read preference secondaryPreferred supports hedged reads on sharded clusters.

Operations read from a random eligible replica set member, irrespective of whether that member is a primary or secondary, based on a specified latency threshold. The operation considers the following when calculating latency:

Read preference nearest supports hedged reads on sharded clusters and enables the hedged read option by default.

The following are common use cases for using non-primary read preference modes:

  • Running systems operations that do not affect the front-end application.

    Note

    Read preferences aren't relevant to direct connections to a single mongod instance. However, in order to perform read operations on a direct connection to a secondary member of a replica set, you must set a read preference, such as secondary.

  • Providing local reads for geographically distributed applications.

    If you have application servers in multiple data centers, you may consider having a geographically distributed replica set and using a non primary or nearest read preference. This allows the client to read from the lowest-latency members, rather than always reading from the primary.

  • Maintaining availability during a failover.

    Use primaryPreferred if you want an application to read from the primary under normal circumstances, but to allow stale reads from secondaries when the primary is unavailable.

In general, do not use secondary and secondaryPreferred to provide extra capacity for reads, because:

  • All members of a replica have roughly equivalent write traffic; as a result, secondaries will service reads at roughly the same rate as the primary.

  • Replication is asynchronous and there is some amount of delay between a successful write operation and its replication to secondaries. Reading from a secondary can return stale data; reading from different secondaries may result in non-monotonic reads.

    Note

    Clients can use Client Sessions and Causal Consistency Guarantees to ensure monotonic reads.

  • Distributing read operations to secondaries can compromise availability if any members of the set become unavailable because the remaining members of the set will need to be able to handle all application requests.

Sharding increases read and write capacity by distributing read and write operations across a group of machines, and is often a better strategy for adding capacity.

See Server Selection Algorithm for more information about the internal application of read preferences.

To avoid stale reads, use primary read preference and "majority" readConcern. If the primary is unavailable, e.g. during elections or when a majority of the replica set is not accessible, read operations using primary read preference produce an error or throw an exception.

In some circumstances, it may be possible for a replica set to temporarily have two primaries; however, only one primary will be capable of confirming writes with the "majority" write concern.

  • A partial network partition may segregate a primary (P old) into a partition with a minority of the nodes, while the other side of the partition contains a majority of nodes. The partition with the majority will elect a new primary (P new), but for a brief period, the old primary (P old) may still continue to serve reads and writes, as it has not yet detected that it can only see a minority of nodes in the replica set. During this period, if the old primary (P old) is still visible to clients as a primary, reads from this primary may reflect stale data.

  • A primary (P old) may become unresponsive, which will trigger an election and a new primary (P new) can be elected, serving reads and writes. If the unresponsive primary (P old) starts responding again, two primaries will be visible for a brief period. The brief period will end when P old steps down. However, during the brief period, clients might read from the old primary P old, which can provide stale data.

To increase consistency, you can disable automatic failover; however, disabling automatic failover sacrifices availability.

To permit read operations when possible, use primaryPreferred. When there's a primary you will get consistent reads [1], but if there is no primary you can still query secondaries. However, when using this read mode, consider the situation described in secondary vs secondaryPreferred.

[1] In some circumstances, two nodes in a replica set may transiently believe that they are the primary, but at most, one of them will be able to complete writes with { w: "majority" } write concern. The node that can complete { w: "majority" } writes is the current primary, and the other node is a former primary that has not yet recognized its demotion, typically due to a network partition. When this occurs, clients that connect to the former primary may observe stale data despite having requested read preference primary, and new writes to the former primary will eventually roll back.

To always read from a low-latency node, use nearest. The driver or mongos will read from the nearest member and those no more than 15 milliseconds [2] further away than the nearest member.

nearest does not guarantee consistency. If the nearest member to your application server is a secondary with some replication lag, queries could return stale data. nearest only reflects network distance and does not reflect I/O or CPU load.

[2] This threshold is configurable. See localPingThresholdMs for mongos or your driver documentation for the appropriate setting.

If the members of a replica set are geographically distributed, you can create replica tags based that reflect the location of the instance and then configure your application to query the members nearby.

For example, if members in "east" and "west" data centers are tagged {'dc': 'east'} and {'dc': 'west'}, your application servers in the east data center can read from nearby members with the following read preference:

db.collection.find().readPref('nearest', [ { 'dc': 'east' } ])

Although nearest already favors members with low network latency, including the tag makes the choice more predictable.

For specific dedicated queries (e.g. ETL, reporting), you may shift the read load from the primary by using the secondary read preference mode. For this use case, the secondary mode is preferable to the secondaryPreferred mode because secondaryPreferred risks the following situation: if all secondaries are unavailable and your replica set has enough arbiters [3] to prevent the primary from stepping down, then the primary will receive all traffic from the clients. If the primary is unable to handle this load, the queries will compete with the writes. For this reason, use read preference secondary to distribute these specific dedicated queries instead of secondaryPreferred.

[3] In general, avoid deploying arbiters in replica sets and use an odd number of data-bearing nodes instead. If you must deploy arbiters, avoid deploying more than one arbiter per replica set.

Back

Read Preference