Docs Menu
Docs Home
/
MongoDB Manual
/
Sharding
/
Administration

Add a Member to a Shard

On this page

  • About This Task
  • Before You Begin
  • Steps
  • Next Steps

You can add members to an existing shard in a sharded cluster. You might want to add a member to a shard for the same reasons you'd want to add a member to any replica set. For example, increasing the number of members provides additional candidates to replace a primary in the event of a failover. Additional members also increase data redundancy and replica set availability.

For more information, refer to Replica Set Deployment Architectures.

About This Task

Before MongoDB 5.0, a newly added secondary still counts as a voting member even though it can neither serve reads nor become primary until its data is consistent. If you are running a MongoDB version earlier than 5.0 and add a secondary with its votes and priority settings greater than zero, this can lead to a case where a majority of the voting members are online but no primary can be elected. To avoid such situations, consider adding the new secondary initially with priority :0 and votes :0. Then, run rs.status() to ensure the member has transitioned into SECONDARY state. Finally, use rs.reconfig() to update its priority and votes.

Before You Begin

To add a member to a shard replica set, you need:

  1. An active sharded cluster replica set.

  2. A new host server for the new member. The new host server must be able to support your sharded data set and be accessible by the active replica set through the network.

Steps

1

Prepare the Data Directory

Prepare the new member's data directory using one of the following strategies:

  • Have the new member automatically sync data from an existing member. This process takes time but does not require administrator intervention.

    Make sure the new member's data directory does not contain data. The new member will copy the data from an existing member.

    If the new member is in a recovering state, it must exit and become a secondary before MongoDB can copy all data as part of the replication process.

  • Manually copy the data directory from an existing member. The new member becomes a secondary member and will catch up to the current state of the replica set. Copying the data over may shorten the amount of time it takes for the new member to sync with the other replica set members.

    Ensure that you can copy the data directory to the new member and begin replication within the window allowed by the oplog. Otherwise, the new instance will have to perform an initial sync, which completely resynchronizes the data, as described in Resync a Member of a Replica Set.

    To check the current state of replica set members with regards to the oplog, use rs.printReplicationInfo().

For background on replication deployment patterns, see the Replica Set Deployment Architectures document.

2

Start the new mongod instance

Specify the data directory and the replica set name. The following example specifies the /srv/mongodb/db0 data directory and the rs0 replica set:

mongod --dbpath /srv/mongodb/db0 --replSet rs0  --bind_ip localhost,<ip address of the mongod host>

Warning

Before you bind your instance to a publicly-accessible IP address, you must secure your cluster from unauthorized access. For a complete list of security recommendations, see Security Checklist. At minimum, consider enabling authentication and hardening network infrastructure.

For more information on configuration options, see the mongod manual page.

Tip

You can specify the data directory, replica set name, and the ip binding in the mongod.conf configuration file, and start the mongod with the following command:

mongod --config /etc/mongod.conf
3

Connect to the replica set's primary

You can only add members while connected to the primary. To connect to the primary, use mongosh. Replace the host and port values with relevant values for your deployment:

mongosh --host mongodb0.example.com --port 28015

If you do not know which member is the primary, connect to any member of the replica set and issue the db.hello() command.

4

Use rs.add() to add the new member to the replica set

Pass the member configuration document to the method. For example, to add a member at host mongodb3.example.net, issue the following command:

rs.add( { host: "mongodb3.example.net:27017", priority: 0, votes: 0 } )
5

Ensure that the new member has reached SECONDARY state

To check the state of the replica set members, run rs.status():

rs.status()

Next Steps

Once the newly added member has transitioned into SECONDARY state, use rs.reconfig() to update the newly added member's priority and votes if needed.

Warning

  • The rs.reconfig() shell method can force the current primary to step down, which causes an election. When the primary steps down, the mongod closes all client connections. While this typically takes 10-20 seconds, try to make these changes during scheduled maintenance periods.

  • Avoid reconfiguring replica sets that contain members of different MongoDB versions as validation rules may differ across MongoDB versions.

Example

If rs.conf() returns the configuration document for mongodb3.example.net:27017 as the fifth element in the members array, to update its priority and votes to 1, use the following sequence of operations:

var cfg = rs.conf();
cfg.members[4].priority = 1
cfg.members[4].votes = 1
rs.reconfig(cfg)

Back

Add Shards to a Cluster